|
|
Genesis of new ultra-fine particles of milling stock in the course of the mill exposure.
Kejík, Pavel ; Pekař, Miloslav (referee) ; Svěrák, Tomáš (advisor)
This work deals with the study of limestone and corundum dry milling using attritor-type stirred mill in a batch mode. There were stearin and polyethylene glycol used as surfactants and spherical shaped steel grinding elements used for the experimental part of the work. The main idea was to examine behavior of the selected grinding stock type within a long-term grinding forces exposure in selected conditions of ultrafine dry milling leading up to the submicron area. Characterization of samples was performed by laser granulometry, X-ray powder diffraction analysis, flame atomic absorption spectroscopy, objective color determination and electrokinetic potential measurement. Experimetaly measured data implies that in all cases there was a re-agglomeration of the grinding stock particles occurring, although in different stages of the disintegration process and in mutually various degree. The analysis results denote that a larger erosion of the crystal structures with the associated increase of the amorphous phase in the submicron particle size took place in the grinding stock.
|
|
|
Final machining technology of a special bearing ring using a grinder on the holes
Růžička, Daniel ; Kalivoda, Milan (referee) ; Chladil, Josef (advisor)
The main goal of this thesis is to compare 5 chosen grinding wheels, that vary by the material and structure. The testing is done in the company SLB, spol. s r.o., using a grinder on the holes BDU 80, which is set to 6 different settings of the grinding cycle, defined by the letters A´, A, B, C, D and E. These settings vary by the cutting conditions and enable to compare the tested grinding wheels by 8 measured parameters of the surface quality of the grinded bearing orbits of outer rings of the SLB 84-74 bearings, that are described by the drawing documentation.
|
|
| |
|
|
Preparation of ceramic-metal composites for ballistic protection
Hladík, Jakub ; Roleček, Jakub (referee) ; Salamon, David (advisor)
Cílem této práce je příprava keramicko-kovového kompozitu pro balistickou ochranu. Přičemž velká pozornost se klade na rozhraní obou materiálů. Práce popisuje jak vlastnosti používaných keramik a kovů, tak i aplikovatelné mechanické testy Kompozit na bázi oxidu hlinitého a hliníků byl experimentálně připraven metodou gravitačního lití / slinování hliníků, která vedla ke spojení s korundovými hexagony. K dosažení optimálního výsledku a co nejnižší teplotě lití bylo třeba vyzkoušet několik teplotních režimů. Připravené vzorky byly balisticky testovány na základě norem NIJ Standard- 0108.01 a NATO Standard STANAG 2280. Vlastnosti rozhraní byly ověřeny pomocí lomové analýzy vzorků, která zkoumala vzorky poškozené balistickým testováním. Za účelem zkoumání rozhraní byla připraveny speciální zkouška čtyřbodým ohybem. Dále bylo provedeno předběžné zkoumání mikrostruktury hliníku.
|
|
| |
|
|
Changes in some physical properties of the aqueous suspension of corundum powder during ultrafine grinding
Šuleková, Nikola ; Šiler, Pavel (referee) ; Svěrák, Tomáš (advisor)
This thesis is focused on the study of changes in properties of the aqueous suspensions of corundum during ultrafine grinding without and with the addition of grinding activator. Such studies are an important step in optimizing the grinding process properly, because by measuring physical properties of a particulate substance, it is easy to determine the actual fineness of the ground substance and its quality for further processing. For the measurement of granulometry, zeta potential, rheological behavior and turbidity, corundum suspensions in distilled water were prepared in a 1:5 ratio without the addition of grinding activator and with the addition of triethanolamine (TEA), by using a planetary mill. The suspensions showed pseudoplastic behavior and the zeta potential of all samples ranged between -30 and 30 mV, thus the suspensions were rather unstable. During the grinding, the viscosity and turbidity of the samples increased. TEA was not proved to be a suitable activator for wet milling of corundum because of higher degree of fineness achieved during milling without an activator.
|
|
|
Growth of single crystals and their basic characterization.
Hanzlíková, Kateřina ; Pospíšil, Jiří (advisor) ; Matěj, Zdeněk (referee)
Basic methods of single crystals growth have been studied in this bachelor thesis. The preparation of anatase and ruby single crystals has been realized by floating zone method in different compositions of the surrounding atmosphere. Crystallinity of prepared materials has been verified by Laue method. The same method has been used for orientation of the prepared single crystals along the principal crystallographic axes. The tetragonal structure of TiO2 has been proved by powder X-ray diffraction. The floating zone method has been found as a very suitable and effective method to grow anatase single crystals.
|
|
| |
|
|
Preparation of ceramic-metal composites for ballistic protection
Hladík, Jakub ; Roleček, Jakub (referee) ; Salamon, David (advisor)
Cílem této práce je příprava keramicko-kovového kompozitu pro balistickou ochranu. Přičemž velká pozornost se klade na rozhraní obou materiálů. Práce popisuje jak vlastnosti používaných keramik a kovů, tak i aplikovatelné mechanické testy Kompozit na bázi oxidu hlinitého a hliníků byl experimentálně připraven metodou gravitačního lití / slinování hliníků, která vedla ke spojení s korundovými hexagony. K dosažení optimálního výsledku a co nejnižší teplotě lití bylo třeba vyzkoušet několik teplotních režimů. Připravené vzorky byly balisticky testovány na základě norem NIJ Standard- 0108.01 a NATO Standard STANAG 2280. Vlastnosti rozhraní byly ověřeny pomocí lomové analýzy vzorků, která zkoumala vzorky poškozené balistickým testováním. Za účelem zkoumání rozhraní byla připraveny speciální zkouška čtyřbodým ohybem. Dále bylo provedeno předběžné zkoumání mikrostruktury hliníku.
|
|
|
Final machining technology of a special bearing ring using a grinder on the holes
Růžička, Daniel ; Kalivoda, Milan (referee) ; Chladil, Josef (advisor)
The main goal of this thesis is to compare 5 chosen grinding wheels, that vary by the material and structure. The testing is done in the company SLB, spol. s r.o., using a grinder on the holes BDU 80, which is set to 6 different settings of the grinding cycle, defined by the letters A´, A, B, C, D and E. These settings vary by the cutting conditions and enable to compare the tested grinding wheels by 8 measured parameters of the surface quality of the grinded bearing orbits of outer rings of the SLB 84-74 bearings, that are described by the drawing documentation.
|
guest ::
